Products
SENACYL
HOME > Products > SENACYL
SENACYL

SPECIFICATION

CYLINDER

Item Specification
Cylinder Bore Size(mm) 40 50 63 80 100 125 140 160 180 200 220 250 320
Rod Diameter(mm) 22 28 36 45 56 63 71 80 90 100 110 160
22 28 36 45 56 71 80 90 100 110 125 140 180
28 36 45 56 71 90 100 110 125 140 160 180
Maximum Stroke(mm) 1000 1600 2000
Maximum Operating Pressure(Mpa) JIS 7 / 14 / 21
MIL(JOHS) 7 / 14 / 21 / 25
Proof Test Pressure(Mpa) 10.5 / 21 / 31.5 / 37.5
Operating Fluid Mineral oil, Water-glycol, Polyol ester, Phosphate ester, Water-in-oil emuision
Cylinder Speed Range(mm/s) 8~500
Operating Temperature(°C) -10~+120
Paint Color Order Coler

SENSOR

Item Specification
Resolution(μm) 1.56
Repetition Accuracy(μm) 10 〔Without load〕
Linearity(mm) 0.15+L/5000 L:stroke
Protection Structure IP67
Vibration Resistance 1.96X102m/s2 (20G), 200Hz, up/down 4h, forward/back 2h,
conforms to JIS D 1601 standard
Shock Resistance 4.9X103m/s2 (500G), 0.5ms, up/down・forward/back ×3 times,
conforms to JIS C 5026 standard

THEORETICAL CYLINDER THRUST VALUES AT VARIED OPERATING PRESSURES

Bore Size(mm) Cross-sectional area of Cylinder(cm2) Rod Diameter(mm) Cross-sectional area of Piston Rod(cm2) Area of Piston's Face(cm2) Cylinder Thurust(kN)
7MPa 14MPa 21MPa 25MPa
40 12.6 Push 12.6 8.8 17.6 26.5 31.5
22.4(B) 3.9 Pull 8.7 6.1 12.2 18.3 21.8
28(A) 6.2 6.4 4.5 9.0 13.4 16.0
50 19.6 Push 19.6 13.7 27.4 41.2 49.0
22.4(C) 3.9 Pull 15.7 11.0 22.0 33.0 39.3
28(B) 6.2 13.4 9.4 18.8 28.1 33.5
36(A) 10.2 9.4 6.6 13.2 19.7 23.5
63 31.2 Push 31.2 21.8 43.7 65.5 78.0
28(C) 6.2 Pull 25.0 17.5 35.0 52.5 62.5
36(B) 10.2 21.0 14.7 29.4 44.1 52.5
45(A) 15.9 15.3 10.7 21.4 32.1 38.3
80 50.3 Push 50.3 35.2 70.4 105.6 125.8
36(C) 10.2 Pull 40.1 28.1 56.1 84.2 100.3
45(B) 15.9 34.4 24.1 48.2 72.2 86.0
56(A) 24.6 25.7 18.0 36.0 54.0 64.3
100 78.5 Push 78.5 55.0 109.9 164.9 196.3
45(C) 15.9 Pull 62.6 43.8 37.6 131.5 156.5
56(B) 24.6 53.9 37.7 75.5 113.2 134.8
71(A) 39.6 38.9 27.2 54.5 81.7 97.3
125 122.7 Push 122.7 85.9 171.8 257.7 306.8
56(C) 24.6 Pull 98.1 68.7 137.3 206.0 245.3
71(B) 39.6 83.1 58.2 116.3 174.5 207.8
90(A) 63.6 59.1 41.4 82.7 124.1 147.8
140 153.9 Push 153.9 107.7 215.5 323.2 384.8
63(C) 31.2 Pull 122.7 85.9 171.8 257.7 306.8
80(B) 50.3 103.6 72.5 145.0 217.6 259.0
100(A) 78.5 75.4 52.8 105.6 158.3 188.5
160 201.1 Push 201.1 140.8 281.5 422.3 502.8
71(C) 39.6 Pull 161.5 113.1 226.1 339.2 403.8
90(B) 63.6 137.5 96.3 192.5 288.8 343.8
110(A) 95.0 106.1 74.3 148.5 222.8 265.3
180 254.5 Push 254.5 178.2 356.3 534.5 636.3
80(C) 50.3 Pull 131.8 92.3 184.5 276.8 329.5
100(B) 78.5 176.0 123.2 246.4 369.6 440.0
125(A) 122.7 204.2 142.9 285.9 428.8 510.5
200 314.2 Push 314.2 219.9 439.9 659.8 785.5
90(C) 63.6 Pull 250.6 175.4 350.8 526.3 626.5
110(B) 95.0 219.2 153.4 306.9 460.3 548.0
140(A) 153.9 160.3 112.2 224.4 336.6 400.8
220 380.1 Push 380.1 266.1 532.1 798.2 950.3
100(C) 78.5 Pull 301.6 211.1 422.2 633.4 754.0
125(B) 122.7 257.4 180.2 360.4 540.5 643.5
160(A) 201.1 179.0 125.3 250.6 375.9 447.5
250 490.9 Push 490.9 343.6 687.3 1030.9 1227.3
110(C) 95.0 Pull 395.9 277.1 554.3 831.4 989.8
140(B) 153.9 337.0 235.9 471.8 707.7 842.5
180(A) 254.5 236.4 165.5 331.0 496.4 591.0

MODEL CODE

MODEL CODE
Item Code Description
1 Model Classification C Senacyl
2 Sensor Type L LR・・・Line Resolver
D LR・・・Line Resolver(Double Rod Cylinder)
I IR・・・Inner Resolver
C CIC・・・Cylscale
3 Cylinder Type M MIL(JHOS) Type
J JIS Type
A Air Cylinder
4 Rod Diameter(mm)
5 Cylinder Bore Size(mm)
6 Stroke(mm)
7 Mounting Style LA Foot/Side Lugs
LB Side End Foot
FA Flange on Rod End Side
FB Flange on Head End Side
CA Clevis/Single
CB Clevis/ Double
TA Trunnion on Rod End Side
TB Trunnion on Head End Side
TC Intermediate Fixed Trunnion
8 Maximum Operating Pressure(Mpa)
9 Cushion B Both End of Cylinder
R Rod End
H Head End
N None
10 Lead Cable and Connector D Connector + No Cable
B Heart Resistant-cable + Connector
Z Heart Resistant-cable + No Connector
11 Lead Cable Length(m)

OUTLINE -CLM TYPE-

SD : BASIC TYPE

SD(BASIC)

Bore
size
Rod
code
A B C D DD E F G H J K L M N P Q R S T U PP
(JIS B2291)
W
Standard Long
stud
Standard Long
stud
Standard Tie
rod
40 A 28 M24×1.5 35 55 24 15 29 18 56 64 54 286 141 118 350 370 11 80 62 32 17 M10×1.5 M10×1.5 SSA15 94
B 22.4 M20×1.5 30 45 19 10 345 360
50 A 36 M30×1.5 45 65 30 15 29 18 56 68 54 290 141 122 364 384 13 90 68 32 17 M12×1.75 M12×1.5 SSA15 94
B 28 M24×1.5 35 55 24 15 354 374
63 A 45 M39×1.5 60 85 41 20 40 20 68 87 54 323 155 141 423 448 14 110 80 32 17 M14×2 M14×1.5 SSA15 94
B 36 M30×1.5 45 65 30 15 408 428
80 A 56 M48×1.5 75 105 50 20 33 26 73 97 58 348 164 155 456 486 16 127 98 32 17 M16×1.5 M16×1.5 SSA20 94
B 45 M39×1.5 60 85 41 20 441 466
100 A 71 M64×2 95 140 65 25 39 31 85 96 58 375 192 154 509 554 19 154 120 32 23 M20×2.5 M20×1.5 SSA20 105
B 56 M48×1.5 75 105 50 20 489 519
125 A 90 M80×2 120 175 85 30 44 36 103 106 68 418 210 174 582 637 22 188 144 40 23 M24×3 M24×1.5 SSA25 105
B 71 M64×2 95 140 65 25 557 602
140 A 100 M95×2 140 210 95 30 49 36 103 116 68 428 210 184 617 687 26 212 162 40 23 M27×3 M27×1.5 SSA25 105
B 80 M72×2 110 160 75 30 587 637


LA : Foot/Side Lugs

LA

Bore
size
Rod
code
A B C E F L M N P Q PP
(JIS B 2291)
LA LB LC LD LE LF LP LG LH LJ LK LM LN W
Standard Long
stud
Standard Long
stud
40 A 28 M24×1.5 35 55 29 - 141 118 350 370 11 80 SSA15 125±0.5 155 20 60±0.15 100 14 28 169 120 28 28 28 26 94
B 22.4 M20×1.5 30 45 345 360
50 A 36 M30×1.5 45 65 29 - 141 122 364 384 13 90 SSA15 140±0.5 175 20 65±0.15 110 16 32 169 120 28 28 24 30 94
B 28 M24×1.5 35 55 354 374
63 A 45 M39×1.5 60 85 40 - 155 141 423 448 14 110 SSA15 155±0.5 190 25 70±0.15 125 18 35 189 150 35 33 30 24 94
B 36 M30×1.5 45 65 408 428
80 A 56 M48×1.5 75 105 33 - 164 155 456 486 16 127 SSA20 180±0.5 220 30 80±0.25 143.5 20 39 189 165 36 37 31 27 94
B 45 M39×1.5 60 85 441 466
100 A 71 M64×2 95 140 39 - 192 154 509 554 19 154 SSA20 220±0.5 265 35 95±0.25 172 24 46 220 165 45 40 29 29 105
B 56 M48×1.5 75 105 489 519
125 A 90 M80×2 120 175 44 - 210 174 582 637 22 188 SSA25 275±0.8 330 40 115±0.25 209 30 55 235 195 50 53 36 32 105
B 71 M64×2 95 140 557 602
140 A 100 M95×2 140 210 49 - 210 184 617 687 26 212 SSA25 305±0.8 365 45 125±0.25 231 33 62 240 200 50 53 31 37 105
B 80 M72×2 110 160 587 637


FA : Flange on Rod End Side

FA

Bore
size
Rod
code
A B C M N P Q PP
(JIS B 2291)
FA FB FC FD FE FF AG AH AK W
Standard Long
stud
Standard Long
stud
40 A 28 M24×1.5 35 55 118 350 370 11 80 SSA15 125±0.5 155 55±0.3 85 14 15 47 123 279 94
B 22.4 M20×1.5 30 45 345 360
50 A 36 M30×1.5 45 65 122 364 384 13 90 SSA15 140±0.5 175 60±0.3 95 16 20 47 123 285 94
B 28 M24×1.5 35 55 354 374
63 A 45 M39×1.5 60 85 141 423 448 14 110 SSA15 155±0.5 190 75±0.5 110 18 25 60 135 317 94
B 36 M30×1.5 45 65 408 428
80 A 56 M48×1.5 75 105 155 456 486 16 127 SSA20 180±0.5 220 90±0.5 130 20 25 59 138 338 94
B 45 M39×1.5 60 85 441 466
100 A 71 M64×2 95 140 154 509 554 19 154 SSA20 220±0.5 265 115±0.5 160 24 30 70 161 363 105
B 56 M48×1.5 75 105 489 519
125 A 90 M80×2 120 175 174 582 637 22 188 SSA25 275±0.8 330 145±0.5 200 30 35 80 174 404 105
B 71 M64×2 95 140 557 602
140 A 100 M95×2 140 210 184 617 687 26 212 SSA25 305±0.8 365 160±0.5 220 33 40 85 174 418 105
B 80 M72×2 110 160 587 637


FB : Flange on Head End Side

FB

Bore
size
Rod
code
A B C L M N Q U PP
(JIS B 2291)
FA FB FC FD FE FF BN
Standard Long
stud
Standard Long
stud
40 A 28 M24×1.5 35 55 141 118 323 280 80 26 SSA15 125±0.5 155 55±0.3 85 14 15 327
B 22.4 M20×1.5 30 45 313 47
50 A 36 M30×1.5 45 65 141 122 337 290 90 27 SSA15 140±0.5 175 60±0.3 95 16 20 337
B 28 M24×1.5 35 55 327 47
63 A 45 M39×1.5 60 85 155 141 415 360 110 45 SSA15 155±0.5 190 75±0.5 110 18 25 393
B 36 M30×1.5 45 65 395 61
80 A 56 M48×1.5 75 105 164 155 462 383 127 34 SSA20 180±0.5 220 90±0.5 130 20 25 407
B 45 M39×1.5 60 85 442 70
100 A 71 M64×2 95 140 192 154 536 426 154 39 SSA20 220±0.5 265 115±0.5 160 24 30 444
B 56 M48×1.5 75 105 501 87
125 A 90 M80×2 120 175 210 174 637 497 188 44 SSA25 275±0.8 330 145±0.5 200 30 35 497
B 71 M64×2 95 140 602 105
140 A 100 M95×2 140 210 210 184 687 517 212 49 SSA25 305±0.8 365 160±0.5 220 33 40 517
B 80 M72×2 110 160 637 105


CA : Clevis/Single

CA

Bore
size
Rod
code
A B C E L M N Q PP
(JIS B 2291)
CA CC CD CE CF
Standard Long
stud
Standard Long
stud
40 A 28 M24×1.5 35 55 29 141 118 406 426 80 SSA15 371 24 20 30 31.5 -0.1
B 22.4 M20×1.5 30 45 401 416 -0.4
50 A 36 M30×1.5 45 65 29 141 122 430 450 90 SSA15 385 30 25 40 35.5 -0.1
B 28 M24×1.5 35 55 420 440 -0.4
63 A 45 M39×1.5 60 85 40 155 141 495 520 110 SSA15 435 38 31.5 43 40 -0.1
B 36 M30×1.5 45 65 480 500 -0.4
80 A 56 M48×1.5 75 105 33 164 155 542 572 127 SSA20 467 48 40 50 50 -0.1
B 45 M39×1.5 60 85 527 552 -0.4
100 A 71 M64×2 95 140 39 192 154 614 659 154 SSA20 519 60 50 65 63 -0.1
B 56 M48×1.5 75 105 594 624 -0.4
125 A 90 M80×2 120 175 44 210 174 711 766 188 SSA25 591 75 63 82 80 -0.1
B 71 M64×2 95 140 686 731 -0.6
140 A 100 M95×2 140 210 49 210 184 764 834 212 SSA25 624 85 71 93 80 -0.1
B 80 M72×2 110 160 734 784 -0.6


TC : Intermediate Fixed Trunnion

TC

Bore
size
Rod
code
A B C E L M N P Q PP
(JIS B 2291)
TA TB TC TD TE TF TG Min.
stroke
(Standard type)
Min.
installation
size
Standard Long
stud
Standard Long
stud
40 A 28 M24×1.5 35 55 29 47 118 323 353 11 80 SSA15 140 90 -0.1 25 25 2.5 42 229 100 218
B 22.4 M20×1.5 30 45 229 229 -0.5
50 A 36 M30×1.5 45 65 29 47 122 325 355 13 90 SSA15 150 100 -0.1 25 25 2.5 42 231 100 218
B 28 M24×1.5 35 55 231 231 -0.5
63 A 45 M39×1.5 60 85 40 61 141 359.5 417 14 110 SSA15 178 115 -0.1 31.5 31.5 2.5 47 265.5 100 245.5
B 36 M30×1.5 45 65 265.5 265.5 -0.5
80 A 56 M48×1.5 75 105 33 70 155 368.5 435 16 127 SSA20 215 135 -0.1 40 40 3 57 274.5 100 254.5
B 45 M39×1.5 60 85 274.5 274.5 -0.5
100 A 71 M64×2 95 140 39 87 154 413 496.5 19 154 SSA20 265 165 -0.1 50 50 3 67 308 150 293.5
B 56 M48×1.5 75 105 308 308 -0.5
125 A 90 M80×2 120 175 44 105 174 446 565.5 22 188 SSA25 331 205 -0.1 63 63 4 83 341 150 329.5
B 71 M64×2 95 140 341 341 -0.5
140 A 100 M95×2 140 210 49 105 184 456 585.5 26 212 SSA25 367 225 -0.1 71 71 4 93 351 200 339.5
B 80 M72×2 110 160 351 351 -0.5

OPTION

LOCKNUT

LOCKNUT

d H B C
M20×1.5 16 30 34.6
M24×1.5 19 36 41.6
M30×1.5 24 46 53.1
M39×1.5 31 60 69.3
M48×1.5 38 75 86.5
M64×2 51 95 110
M72×2 58 105 121
M80×2 64 115 133
M95×2 76 135 156

SINGLE PROTRUSION END JOINT

SINGLE PROTRUSION END JOINT

Bore size Rod code KK F L CA CT CC CD CF ER J FW Estimated
weight (kg)
40 A M24X1.5 37 42 70 - 28 20 49 25 10 31.5 -0.1 1.0
B M20X1.5 32 -0.4 1.1
50 A M30X1.5 47 54 95 - 41 25 49 30 15 35.5 -0.1 1.2
B M24X1.5 37 -0.4 1.3
63 A M39X1.5 62 72 115 - 43 31.5 62 35 15 40 -0.1 2.2
B M30X1.5 47 -0.4 2.6
80 A M48X1.5 77 90 145 - 55 40 79 40 20 50 -0.1 5.0
B M39X1.5 62 -0.4 5.6
100 A M64X2 97 115 180 - 65 50 100 50 30 63 -0.1 8.1
B M48X1.5 77 -0.4 10.3
125 A M80X2 125 140 220 110 80 63 120 70 30 80 -0.1 18.6
B M64X2 100 115 195 90 -0.6 16.3
140 A M95X2 145 165 255 130 90 71 140 80 30 80 -0.1 27.5
B M72X2 115 130 220 100 -0.6 22.8
160 A M100X2 155 175 275 140 100 80 160 90 40 100 -0.1 40.6
B M80X2 125 145 245 110 -0.6 34.6
180 A M120X2 185 210 325 170 115 90 180 105 40 125 -0.1 69
B M95X2 145 170 285 130 -0.6 55
200 A M130X2 200 230 355 180 125 100 200 115 40 125 -0.1 82
B M100X2 155 185 310 140 -0.6 70
224 A M150X2 230 265 405 210 140 112 220 125 50 140 -0.1 129
B M120X2 185 220 360 170 -0.6 100
250 A M170X3 260 295 455 240 160 125 250 140 60 160 -0.1 169
B M130X2 200 235 395 180 -0.6 140

DOUBLE PROTRUSION END JOINT

DOUBLE PROTRUSION END JOINT
Bore size Rod code KK L CA CB CC CD CF ER CW FW CV CP J Estimated
weight(kg)
40 A M24X1.5 35 90 65 30 20 40 25 16 38 +1.0 9 83 8 1.4
B M20X1.5 30 96 60 +0.1 1.2
50 A M30X1.5 45 110 80 35 25 50 30 17.5 40 +1.0 9 88 15 2.1
B M24X1.5 35 100 70 +0.1 2.0
63 A M39X1.5 60 135 100 40 31.5 70 35 20 45 +1.0 13 105 15 4.3
B M30X1.5 45 120 85 +0.1 4.0
80 A M48X1.5 75 165 125 50 40 80 40 25 55 +2.0 13 125 15 7.5
B M39X1.5 60 150 110 +0.1 7.0
100 A M64X2 95 210 160 65 50 100 50 30 70 +2.0 19.5 158 20 14.1
B M48X1.5 80 195 145 +0.1 13.9
125 A M80X2 120 265 200 80 63 130 65 40 90 +2.0 19.5 195 25 31.0
B M64X2 95 240 175 +0.1 28.0
140 A M95X2 140 305 230 90 71 150 75 40 90 +2.0 19.5 195 30 39.0
B M72X2 110 275 200 +0.1 38.0
160 A M100X2 150 330 250 100 80 160 80 50 110 +2.0 25.5 240 30 58
B M80X2 120 300 220 +0.1 55
180 A M120X2 180 385 295 115 90 180 90 62.5 135 +3.0 25.5 290 40 94
B M95X2 140 345 255 +0.1 88
200 A M130X2 195 420 320 125 100 200 100 62.5 135 +3.0 25.5 290 40 115
B M100X2 150 375 275 +0.1 108
224 A M150X2 225 480 365 140 112 230 115 70 150 +3.0 25.5 320 50 178
B M120X2 180 435 320 +0.1 155
250 A M170X3 255 540 415 160 125 250 125 80 170 +4.0 31.5 370 60 224
B M130X2 195 480 355 +0.1 211

Contact us:
TEL.+81-75-325-2888
Contact us by email

Page Top